Vehicles
262 not categorized PORSCHE 964 EMSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.EIP001N35S Endless ewig n35s racing front brake pads Porsche 964 turbo 91-92 General Fitment911 1989-94911 1994-98
$526.50
Make a selection E19208 Rennline's stainless steel folding race hook install in minutes on any Porsche with factory screw type removable tow hook. Unlike the aluminum units on the market that are usually advertised as "for decorative purposes only", rennline's stainless steel tow hook is a precision machined and will stand up to the extreme abuse seen in any race environment. With a 2" opening as required by most organized race events and screw directly into the factory bumper pull location. Each hook comes with a rubber bumper to be applied on the back side to insure your bumper cover will never get scratched from hook contact. Keep the corner workers and track officials happy by installing a hook that are highly visible and h...(choose a part on the right to read more)
$152.90
Make a selection BES96402000S "brombacher" catalytic bypass pipe for 964 89-94 General Fitment911 1987-89
$226.60
Make a selection FRI0131 Gruppe m ram air intake system Porsche 964 Carrera 88-93 General Fitment911 1987-89
$2,175.08
Make a selection FSPOR964CB Features: General Fitment911 1989-94
From $495.00
Make a selection FSPOR964HFBO Product details: General Fitment911 1989-94
From $85.00
Make a selection FSPOR964PMB Product details: General Fitment911 1989-94
From $395.00
Make a selection FSPOR964SMB Product details: General Fitment911 1989-94
$295.00
Make a selection FVD100110 Rs-look air intake changeover kit for Porsche 964/965 General Fitment911 1989-94
$218.90
Make a selection FSPOR964SROTP Product details: General Fitment911 1989-94
From $225.00
Make a selection FSPOR964TOTP Product details: General Fitment911 1989-94
$450.00
Make a selection FVD110001 Complete throttle housing kit that includes the larger 993 intake manifolds. This includes everything needed for installation. This kit is made for the early 1989 or 1990 964. This throttle housing will allow for the maximum achievable gains shown in our tuning kits. Gains of ranging from 15-50 hp (depending on what modifications you have) can be seen with the addition of this housing and the FVD mass air kit. This includes everything needed for the installation. This kit includes: 1 x updated throttle housing FVD11000 2 x intake manifolds from the 993 4 x intake manifold sleeves 8 x hose clamps sold individually. 1 necessary per car.
$4,270.39
Make a selection FVD1161021 The discs rigid hub with organic friction material has superior thermal resistance, is more resistant to higher rpm's than the oe discs, offers greater longevity and is able to transmit higher torque (370 ft/lbs. / 500 nm max.). It is an ideal kit for lightly modified street or light use track cars. Clutch kit is made in Germany and includes: 1 qty. Clutch disc (zf sachs race engineering, gmbh) 1 qty. Pressure plate (zf sachs race engineering, gmbh) 1 qty. Release bearing 1 qty. Spline lubricant 9 qty. Pressure plate screws kit weighs 13 lbs. (6 kg) tech tip: when you are planning to install a new clutch, it is a good idea to replace the clutch release fork and shaft to ensure proper clutch engagement. Our par...(choose a part on the right to read more) General Fitment911 GT3 2007-11911 GT3 2003-05 911 1994-98 911 1989-94
From $1,144.17
Make a selection FVD116805 Replacing your pressure plate? Take a look at this lightweight model, a savings of over 11 lbs for some models. Made by zf sachs to original specifications for all 964 / 993 and 968 naturally aspirated models. Direct replacement for the oe pressure plate. 240 mm. 3100-3300 lb. Clamp load. Weighs: 9.5 lbs. (4.3 kg) installation notes for those using single mass flywheels: when installing a new pressure plate, be sure to add 9 qty. Pressure plate pan head bolts, our part # 90006710301 and 1 qty. Starter ring gear 96411414331. General Fitment911 1994-98968 1992-95 911 1989-94
From $581.90
Make a selection FSPOR993CFHB Product details: General Fitment911 1994-98
$350.00
Make a selection FVD116925 4 puck sintered metallic material which has a higher thermal capacity than organic friction material. Rigid center hub. Aggressive start performance. Direct replacement for the oe clutch disc. Made in Germany by zf sachs race engineering. Weighs: 2.42 lbs. (1.1 kg) please note: due the aggressive start performance of the sintered disc, we do not recommend this disc for street cars. We also recommend that you purchase a sport / racing pressure plate in conjunction with this disc. This can fit the rs cars but we would recommend the 962 disc, part # FVD 116 838 for the 964 and 993 rs models. The sachs racing clutch discs with sintered metal plates have a higher friction coefficient than plates with organic frictio...(choose a part on the right to read more) General Fitment911 GT3 2003-05911 1994-98 911 1989-94
From $461.16
Make a selection FVD211342 This heater blower bypass tube was originally used on the rennsport and cup models to save weight. It is made of lightweight, polished carbon / kevlar. Please note: for the 993's from 1996+ you must also purchase and additional air duct, part # 96410640302 looking to add more carbon to your engine bay, take a look at our carbon air duct for the intake, part # FVD211343 sold individually. 1 necessary per car. Installation note: this tube snaps inside part # 96410640302. If 96410640302 is very old and has lost its elasticity then fitment can be an issue. We recommend adding qty. 1 of part # 96410640302 in this instance.
$350.90
Make a selection FVD1169281 Higher transmittable torque. Higher clamping load. Less abrasion. Direct replacement for the oe pressure plate. 240 mm. Max torque: 775 lb/ft (1,050 nm)* weighs: 9.5 lbs. (4.3 kg) the reinforced sachs performance pressure plate (clutch cover) has fundamental advantages against an oe pressure plate, such as a higher transmittable torque and higher resistance against thrust. It also allows for faster and sportier gearshifts. That makes it extremely useful for street tuning, endurance races and hill climbing. The sachs performance clutches are assembled by hand. This guarantees the highest quality attributes in clamping load and release characteristics. Installation notes for those with single mass flywheel kits: ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1994-98 968 1992-95 911 1989-94
From $992.73
Make a selection EIP002N35S Endless ewig n35s racing rear brake pads Porsche 964 turbo 91-92 General Fitment911 1989-94
$526.50
Make a selection GT016 This fiberglass replacement deck lid is an exact duplicate of the 1976 930 turbo “whale tail” rear spoiler. One piece deck lid. Inset grille sold separately. This is the famous whale tail first used on the 1976 turbo cars. Add down force and look great with this tail base/deck lid. Gt racing also recommends buying the grill part number rgt16g. Please specify 911 or 964 when ordering. The 964 needs hinge adapters, part number rgt11a. General Fitment911 1974-77911 1978-83 911 1984-86 911 1987-89 930 1975-77
$995.00
Make a selection FVD351425426EQ A quality, cost effective set of replacement "big red" style calipers. These are a direct replacement for the 965 turbo, 993 c4s / rs and 993 turbo but can be installed on many 964 / 993 models with the correct caliper adapters. Please contact your FVD parts specialist for fitment questions. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Also a now is the time to install a set of our speed bleeders, part # FVD910102. They are comparable to part numbers 993 351 425 10 and 993 351 426 10. Please note: these are aftermarket calipers and do not come with the logo or brake pads. Sold individually. 1 necessary per car.
$874.50
Make a selection FVD51202000GFK Rs 1973 gfk ducktail General Fitment911 1989-94911 1970-73
$1,527.57
Make a selection FVD50501900 When you are installing a lightweight bumper or bumper bar for racing use, you want to remove as much weight as possible. Don't forget to remove your heavy factory supports. These are a lightweight alternative and are made in Germany. Weighs: .3 kilograms ( .33 lbs ) sold individually. 2 needed for the rear or front bumper. Measurements shown are in centimeters. Please note: these fit the 928 87-91 front bumper, 964 / 965 89-94 front bumper, 993 94-98 rear bumper. Please check the model fitment tab to ensure accurate fitment. General Fitment911 GT3 2003-05911 TURBO/GT2 2001-05 911 1998-05
From $141.90
Make a selection FVD51201001KEV Vacuum pulled carbon deck lid General Fitment911 1989-94
$1,878.16
Make a selection FVD55246500 High quality polished carbon dash trim piece. Great detail is taken to attempt to match the original weave size, color and polish. Whether you are adding carbon to the interior or matching existing pieces, this is high quality and is made in Germany so it is made to last, like the original. This cover is a carbon replacement for original # 964 552 465 00 01c. Sold individually.
$133.10
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |